At present, the tin- mineral mines produced by various countries' tin- smelting plants are smelted by using tin alloys with higher grades in a matching manner. China has a large number of containing arsenic, antimony high refractory tin, so the late 1970s made many experimental studies. Sulfur vulcanization is very effective in enriching tin, so the process of combining metallurgy and metallurgy is adopted. In the beneficiation process, only a complex tin ore containing arsenic and antimony is produced to increase the recovery rate of tin, and then the complex tin ore is vulcanized in a fumigating furnace to obtain a complex tin soot. The handling of complex tin soot is still in the experimental stage and there are several different processes. One of the processes is shown in Figure 1. The chemical composition (%) of tin used in the test was: 4.96Sn, 4.33Pb, 3.15Sb, 1.77As, 0.025Ag, 0.011In, 0.019Cd, 0.30Cu, 5.99S, 0.30C, 28.95Fe, 0.88CaO, 20.44 SiO 2 , 3.05Al 2 O 3 , the product is sodium stannate. FIG smelting smoke tin complex 1 - adding a base alloy melting - Alkali flooding Process for purifying and concentrating sodium sulphate production by leachate The second process is shown in Figure 2. The chemical composition (%) of the tin soot used in the test was: 21.26Sn, 17.92Pb, 9.73As, 12.56Sb, 5.03Zn, 0.041Ag, 0.047In, 0.19Cd, 3.79S, 2.63Fe, 0.29CaO, 3.28SiO 2 . The phase analysis is shown in the table below. The product is tin- lead alloy. Figure 2 High arsenic bismuth polymetallic tin soot reduction roasting (twice) arsenic removal 锑 Reduction smelting-electrolytic refining process for producing tin-lead alloy Phase analysis of high arsenic bismuth polymetallic tin soot /% tin lead arsenic antimony Zinc Phase content Phase content Phase content Phase content Phase content SnO SnO 2 Sn 5.7 87.9 6.2 PbSO 4 PbO PbS Insoluble slag 25.1 57.1 5.5 11.7 As 2 O 3 M3(AsO 4 ) 2 As As 2 S 3 32.3 57.5 1.9 8.3 Sb 2 O 3 Sb 2 S 3 M3(SbO 4 ) 2 21.6 4.3 74.1 ZnO ZnS Insoluble slag 6.2 84.8 0.9 The third process is shown in Figure 3. The chemical composition (%) of the sample was: 23.28Sn, 11.81Sb, 20.74Pb, 4.79Zn, 0.055Ag, 2.56S, 6.42As, 1.85Fe, 0.004Bi, 0.81CaO, 2.79SiO 2 , 2.79SiO 2 , 1.20Al 2 O 3 , 0.047In. This is a combination of wet and fire method. The chlorination reduction leaching method is used to completely separate arsenic at one time; and the associated elements such as bismuth, lead, zinc, silver and iron can be completely removed, and then enter the traditional Fire process. Figure 3 CR (chlorination reduction leaching distillation) treatment Principle process of high arsenic and antimony metal tin soot
The main function of the edge banding is to seal the cross-section of the board, so as to avoid the damage of the board and the adverse factors (mainly moisture) in the process of use and prevent the formaldehyde inside the board from volatilizing, and at the same time achieve the effect of beautiful decoration.
The product has the following main features: smooth surface, no blistering, no ribbing, moderate gloss, smooth surface and back surface, uniform thickness, uniform width, reasonable hardness, high elasticity, good quality, strong wear resistance, trimmed and sealed The color of the side and the side is close to the surface color, not whitish, good gloss, and the overall color of the finished furniture is coordinated.
PVC furniture edge banding is relatively light, which is relative to metal and plexiglass. The reason for the lightness is not because it is a polymer compound, but because they are organic compounds, which are composed of carbon, hydrogen, oxygen, and chlorine. And other lighter elements. PVC Edge Banding,Edge Banding Pvc,Pvc U Trim Edge Banding,Pvc Edge Banding Trimmer Henan Shunbang Chemical Industry CO.,Ltd , https://www.suspensionpvc.com
The material of pvc furniture edge banding is plastic, which is easy to process. Plastic has plasticity, that is, it deforms after heating or pressurizing, and maintains its original shape after the temperature drops or the pressure disappears. It can be processed into edge bands of their respective shapes by extrusion and other methods, such as T-shaped edge bands, H-shaped edge bands, D-shaped edge bands, V-shaped edge bands, I-shapes, and so on.
pvc furniture edge banding is of high quality and low price, and the price of plastic is far less than that of metal.