A lathe is used to fashion a rotating piece of raw metal, wood, or composite into a precise configuration using movable cutting tools, or bits set to varying depths. The process, known as turning, or machining, is most often accomplished with a horizontal lathe. Often, however, space or material constraints, sometimes even personal preferences, necessitate the use of a vertical lathe. Vertical Lathe,Vertical Lathe Machine,Vertical Turret Lathe,Cnc Vertical Lathe Jiangsu Hoston Machine Tools Co., Ltd. , https://www.haostonmachinetools.com
Cars are now more and more popular, and more and more cars are currently running on the roads. It's really convenient to drive a car at a distance, but cars and people must work and rest. The following Xiao Bian talked about his own experience on the issue of car maintenance.
1, timely cleaning the car
When you run or stop on the road, the car is easily covered with dust particles, bird droppings, etc. Especially after the rain, the acid inside will corrode the paint on the surface of the car, causing the car to be no longer bright and serious. fade.
2, promptly check the replacement of motor oil
The normal operation of the engine and other components of the vehicle will not affect the lubrication and cleaning of the engine oil. Therefore, check the oil scale in time to see if the oil is normal. In general, the new car needs to change its oil every 5,000 kilometers. If the oil filter is dirty, it must be replaced.
3, regular check antifreeze, brake oil, glass water, etc. are sufficient
Antifreeze can ensure the normal driving of the vehicle in winter and it is not easy to freeze. Brake fluid is an essential part of the braking system. Glass water is used to clean glass. These must be ensured in order to allow the normal operation of the vehicle.
4, often check the tire pressure
Normal tire pressure is the premise to ensure that the vehicle is steadily on the road. Tyre pressure is too high to increase the risk of puncture, and it will also reduce comfort. Low tire pressure will increase fuel consumption and increase tire wear. Therefore, you should always check the tire pressure, you can prepare a tire pressure gauge is best. If the forum pattern is smooth, be sure to change the tires in time.
Essentially a horizontal lathe turned on end, a vertical lathe, also called a boring tool, is composed of basically the same parts as a horizontal lathe. As implied, the functions of vertical lathes are performed up and down, rather than side to side, as is the case with horizontal lathes. This vertical alignment allows short, heavy, bulky materials to be machined more efficiently than with a horizontal lathe.
All lathes, vertical or horizontal, are comprised of the same basic parts. The headstock encloses the spindle and chuck, the parts that actually turn the material. The bed catches the shavings, and also serves as a brace for the horizontal lathe. The feedscrew and leadscrew, mounted on the lathe carriage, adjust the speed and distance traveled by the cutters along the stock. The cross slide and compound rest position the toolbox, which, in turn, mounts the bits.
The tailpost, at the opposite end of the lathe spindle, clutches the stock and braces it, thus eliminating wobble and vibration. The headstock and tailpost may be at the upper or lower end of a vertical lathe, or to the right or left end of a horizontal lathe. Either way, the headstock is one end of the lathe, the tailstock, the other.
Vertical lathes may be vertical turret lathes (VTL), where a turret holds various toolboxes, allowing little wasted time resetting bits during the machining process. There are also computer numerical control (CNC) vertical lathes in which the entire machining process is computer operated.
The top of the lathe pyramid are the CNC vertical turret lathe machines, most often used to turn stainless steel into precision parts for engines, turbines, transmissions, etc. These machines, though expensive to purchase and operate, are perfectly suited to the task, saving space, as well as over-stressed equipment. A CNC VTL can also be used on alloys to efficiently turn precision bearings and gears.
A vertical lathe can used on rough wood in a home workshop, mainly for its space-saving attribute. Many home hobbyists, however, simply feel more comfortable turning wood up and down, rather than side to side. Altogether, the vertical lathe is a very capable and versatile tool.